Back To Products     

Custom Number Panels

Call our Customer Service Department to discuss your custom requirements, we will be happy to quote you. Custom Lenses of any kind are readily available for any standard Number Panel.

Chimes, Transformers and Output Cable

 

CH100
Chime, "Optional"

This optional unit is a two-tone door chime that mounts near any Number Panel to pleasantly call attention to the lighting of a number and is operated by the push button chime switch on any Switch Panel. Has a 10-ft. cable to plug in to the nearest Number Panel.

CH100 - Chime, two-tone, wall-mount 10-ft. cable connects to Number Panel, 7" x 5" x 2".

40W 150W
Transformers

All systems are powered by a UL Approved low-voltage Transformer (12-volts) so that the system is safe, no shock hazard, and so that cables may be easily run along base boards, through walls, and in drop-ceiling areas without the use of expensive electrical conduit (most jurisdictions). Transformers have a replaceable fuse to protect the system in case of an electrical "short".

To determine the proper size Transformer required, simply multiply the number of Number Panel lamps in the system by 1.6, this is the "watts required". If the watts required is less than 40 select the 40W Transformer, if more than 40 select the 150W Transformer.

40W - Transformer, 40-watt, 12-volts, w/ fuse & 10-ft. cable, plugs directly into any 110-volt outlet.

150W - Transformer, 150-watt, 12-volt, w/ fuse & 10-ft. cable, & 6-ft. cord for 110-volt outlet.

150W-INT - Transformer, 150-watt, 12-volt, w/ fuse & 10-ft. cable, & 6-ft. cord for 220-volt outlet (International).

Output Cable connects the Switch Panel to the Number Panel, or connects two Number Panels together ("daisy chain"). Cables have connectors at both ends for easy hook-up, no electrician required. When measuring for Output Cable to be sure to allow for routing up and down the walls, over the ceiling, and around any obstacles. Order the proper model cable for the number of stations (switches) on the Switch Panel. For example: A #10KR Switch Panel has (10) switches (ten stations), so order #110CSL, 10-station Output Cable. Maximum recommended cable length is 200-feet. Order by the foot; order Length & Connector Set for each Cable:

11L - Output Cable, 1-station / 11CS - Connector Set for 11L Cable
15L - Output Cable, 5-station / 15CS - Connector Set for 15L Cable
110L - Output Cable, 10-station / 110CS - Connector Set for 110L Cable
115L - Output Cable, 15-station / 115CS - Connector Set for 115L Cable
120L - Output Cable, 20-station / 120CS - Connector Set for 120L Cable
130L - Output Cable, 30-station / 130CS - Connector Set for 130L Cable
140L - Output Cable, 40-station / 140CS - Connector Set for 140L Cable
150L - Output Cable, 50-station / 150CS - Connector Set for 150L Cable

Output Cable "Y-Adaptors"

These "Y-Adaptors" provide easy hook-up for all system configurations. Use a "Dual Y-Adaptor" at the Switch Panel if two Number Panels are in opposite directions, keeps Output Cable lengths as short as possible. Use a "Split Y-Adaptor" if the Switch Panel output is being "split" into two different No. Panels. For example, a 10-station Switch Panel, #1-10, can be split to go to two 5-station Number Panels, #1-5 and #6-10. Use a DUAL-NP1 to "daisy chain" from one 10-station Number Panel to another, use (2) for 20-station, etc.

DUAL-1 - Y-Adaptor, Dual Output any 5 or 10-station Switch Panels.
DUAL-2 - Y-Adaptor, Dual Output, for 15/20 PL Switch Panels only.
DUAL-3 - Y-Adaptor, Dual Output, for 20CP/KR Switch Panels only.
SPLIT-1 - Y-Adaptor, Split Output, for 10PL Switch Panels only.
SPLIT-2 - Y-Adaptor, Split Output, for 10CP/KR Switch Panels only.
SPLIT-3 - Y-Adaptor, Split Output, for 15PL Switch Panels only.
SPLIT-4 - Y-Adaptor, Split Output, for 20PL Switch Panels only.
DUAL-NP1 - Y-Adaptor, to "daisy chain" any 10-station Number Panels.